Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Burlingame
Gate installation in Burlingame, CA typically runs $3,200-$8,500 for a complete residential system, with most homeowners receiving a written quote within 24 hours of our free site visit. We dispatch crews to Burlingame from our San Francisco Bay Area office, and our technicians know the specific challenges of installing gates where salt-laden marine layer meets steep Peninsula grades and century-old wrought iron. Call (628) 270-2709 to schedule a free measure and written estimate - under Haven Standard Clause 1, you’ll have the full price in hand before any work starts.
Why Vance Gate Repair Oakland Is Burlingame’s Preferred Gate Installation Company
We’ve completed gate installations throughout Burlingame’s distinct neighborhoods - from the original wrought iron estates of Burlingame Park to the hillside homes near the Hillsborough border - and our job records show a pattern: salt corrosion and grade-compensating hardware are the two details that separate a lasting installation from one that sags or seizes within two years.
Our Gate Installation in Burlingame customers receive the same documentation protocol we developed on commercial access-control sites starting in 2014: a written scope, a written price, and a photographed record of every hinge setting, operator seal, and safety-device alignment before we leave. Under Clause 4 (Evidence on every job), that photo log stays with you and in our files.
A live person answers our phones 24 hours a day, seven days a week - no voicemail loop, no callback queue. When you call (628) 270-2709, you’ll speak with someone who can schedule your free Burlingame estimate immediately.
Our 365-Day Done Right Promise covers every installation: if anything isn’t right, we make it right with no argument, no fee, no expiration within that full year.
Our Gate Installation Services in Burlingame
Driveway Gate Installation
Most Burlingame driveway gates we install are replacing original 1920s-1950s systems on homes in Easton Addition, Burlingame Park, or the streets climbing toward Hillsborough. A typical new driveway gate installation in Burlingame runs $4,800-$8,500, including posts, hardware, and automation. We specify stainless or galvanized hinge pins and posts rated for salt-air exposure - standard painted steel starts showing rust within 18 months here. For sloped driveways, we calculate uphill-biased hinge geometry so the gate doesn’t sag toward the street.
Swing Gate Installation
Swing gates are the most common style in Burlingame’s older neighborhoods, but they’re also the most sensitive to grade. A single swing gate installation typically costs $3,200-$5,800; a double swing runs $5,500-$8,200. We recently installed a LiftMaster swing gate operator on a steep driveway off El Camino Real near the Hillsborough border, where the original wrought iron gate had corroded hinges and a failing post footing. Our tech used stainless hinge pins and an uphill-biased hinge geometry to compensate for the slope, then sealed the operator to IP55 and added a safety photocell. The gate now opens smoothly despite the grade and daily salt fog.
Sliding Gate Installation
Sliding gates work well on Burlingame’s narrower lots where a swing arc would encroach on driveway parking space. Typical installation runs $4,500-$7,800. The track and roller system must be specified for marine environments - we use sealed bearing rollers and galvanized track, never standard steel that will pit and bind. For properties on the bay side of El Camino Real, where fog is heaviest, we add stainless track covers to reduce salt buildup in the guide channel.
Pedestrian Gate Installation
Pedestrian gates in Burlingame often match existing driveway gates on period homes, requiring custom fabrication rather than catalog units. A basic pedestrian gate installation starts around $2,400; period-sympathetic custom work with matching scrollwork and hardware runs $3,800-$6,200. We source or fabricate hinges and latches that visually match original 1920s-1950s hardware while using modern stainless or brass internals that resist the marine layer.
Security Gate Installation
Security gates in Burlingame combine access control with the city’s architectural character requirements. A full security gate system with keypad, intercom, and automated operator typically runs $6,500-$12,000 depending on access-control complexity. We install Linear and Viking operators with IP55 sealing as minimum specification for coastal Burlingame, and we document every wire run and device setting under Haven Standard Clause 4 so future service calls don’t require rediscovery.
Double Gate Installation
Double gates suit the wider entries common on Burlingame’s pre-war estates. Installation runs $5,500-$9,200 with automation. The critical detail on double gates is synchronized operator timing - if one leaf lags, the center latch won’t align. We set and photograph limit-switch positions on both operators so you have a baseline if drift occurs.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Before
AfterTrusted Brands We Service in Burlingame
We install and service nine major automation brands - LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule - and we stock common operator models and parts for Burlingame customers to avoid the two-week wait that comes with special orders. For coastal Burlingame installations, we typically recommend Linear or Viking operators with factory IP55 sealing, as both manufacturers build housings that withstand salt-air penetration better than standard residential models. We don’t steer customers toward replacement when repair is viable, and we don’t push any single brand - we install what fits your gate, your grade, and your access-control needs.
Common Gate Installation Problems We See in Burlingame Homes
- Corroded hinge hardware on original wrought iron gates. Hinges and latch hardware on original wrought iron gates corrode and seize within 2-3 years due to salt-laden marine layer, causing sag and misalignment. We specify stainless or galvanized replacement hinges, never standard painted steel, and we document the original hardware pattern before removal so period-sympathetic matching is possible.
- Premature operator board failure from moisture penetration. Automatic gate operator circuit boards fail prematurely when not sealed to IP55, as salt moisture penetrates standard housings. Every operator we install in Burlingame is sealed to at least IP55, and we photograph the seal integrity before closing the housing.
- Sag and misalignment on sloped driveways. Steep driveways near the Hillsborough border cause swing gates to sag at the hinge post because hardware is installed with flat-lot geometry, leading to premature wear. We measure grade angle during our free site visit and specify uphill-biased hinges or gravity-compensating closers where needed.
- Failed post footings in aging masonry. Original stone or brick pilasters on 1920s-1950s homes often have degraded mortar or inadequate steel reinforcement for modern automated gates. We assess footing integrity before hanging new gates, and we rebuild or sister posts when necessary - documented with photos, with the structural findings written into your scope.
Pricing for Gate Installation in Burlingame, CA
A typical swing gate installation in Burlingame runs $3,200-$5,800 for a single leaf, $5,500-$8,200 for double. Sliding gates range $4,500-$7,800. Driveway gate systems with automation average $4,800-$8,500. Security gates with access control start around $6,500 and can reach $12,000 depending on intercom, keypad, and remote-entry complexity.
What moves the price: grade compensation hardware on sloped lots (add $400-$800), custom period-sympathetic fabrication for historic homes (add $1,200-$3,500), and footing rebuilds where original masonry won’t support automated loads (add $800-$2,400). Every price is written and agreed before work starts - no verbal estimates, no surprise invoice at the end. Free estimates include full site measurement, grade assessment, and a written scope with line-item pricing. Call (628) 270-2709 to schedule.
| Gate Type | Typical Range in Burlingame |
|---|---|
| Single Swing Gate | $3,200 - $5,800 |
| Double Swing Gate | $5,500 - $8,200 |
| Sliding Gate | $4,500 - $7,800 |
| Driveway Gate (with automation) | $4,800 - $8,500 |
| Pedestrian Gate | $2,400 - $6,200 |
| Security Gate (with access control) | $6,500 - $12,000 |
We Also Serve Cities Near Burlingame
Our Gate Installation crews work throughout the Peninsula, including San Mateo, Redwood City, Atherton, and Menlo Park. Each city gets the same Haven Standard protocol - written price before work, documented photo record after - but the hardware specifications differ: inland cities don’t require the same corrosion resistance that Burlingame’s salt air demands.
Serving Burlingame, CA - Our Local Coverage Area
We’re based in the Burlingame area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Burlingame
Stainless steel or hot-dip galvanized hardware lasts 3-4 times longer than standard painted steel in Burlingame’s marine environment. We specify 316 stainless for hinge pins and galvanized posts with powder-coated surfaces - never bare or painted steel that will show rust within two years. Call (628) 270-2709 and we’ll show you the material difference on your estimate.
Original 1920s-1950s wrought iron gates in Burlingame Park and Easton Addition were built for manual operation with hardware patterns no longer in production, so off-the-shelf replacement hinges and latches won’t fit or match visually. We either fabricate custom hardware to the original pattern or source period-sympathetic components from specialty foundries, then document the installation with photos for future service. Call (628) 270-2709 for a free assessment of your original gate.
Steep driveways near the Hillsborough border cause standard swing gates to sag toward the street because flat-lot hinge geometry doesn’t account for gravity loading on the downhill side. We measure grade angle during our free site visit and specify uphill-biased hinges, gravity-compensating closers, or reinforced posts to counteract the slope - details that prevent the premature hinge wear and misalignment we see on gates installed without grade compensation. Call (628) 270-2709 to schedule a site measure.
California building code requires automatic gates to have entrapment protection - typically safety photocells (infrared beams that stop the gate if crossed) and edge sensors on the leading edge - plus audible and visual warnings before operation. We install and test both, document their function with photos, and provide you the test record under Haven Standard Clause 4. Call (628) 270-2709 and we’ll walk through the specific safety package for your gate type.
Gate operators in Burlingame’s salt-air environment need annual inspection and seal-checking, with hinge and hardware lubrication every 6-8 months - roughly twice the interval inland properties require. Salt moisture penetrates worn seals and corrodes circuit boards, so we inspect IP55 seal integrity, clean photocell lenses, and photograph operator condition during each service visit. Call (628) 270-2709 to set up a maintenance schedule that matches your exposure.
Written by Adrian Vance, Owner at Vance Gate Repair Oakland, serving Burlingame and the Peninsula since 2014.